Right-Angle Planetary Gear Reduction Motor can be installed with 360 degrees without dead angle, flexible installation and saving space.
What are the characteristics of Right-Angle Gear Reduction Motor?
Category Archives: News
How to pass run-in period of DC gear motor safely?
The new DC gear motor is manufactured from factory, which usually needs to pass the run-in period before using. The operation of gear motor during the run-in period has an important impact on the later use. Therefore, we should use the motor in the correct way during the run-in period to ensure that it can safely pass the run-in period.
The run-in period of DC gear motor is very important, so VEER Motor advises our customers carefully take care of your DC gear motor
- Choose lubricating oil reasonably, especially for dc motor with input power greater than 11KW, which load gear oil should be injected.
- At ordinary times, pay more attention to check the lubricating oil, hydraulic oil coolant, and keep the oil level and quality in good, pay attention to check the sealing of the whole gear motor. If too much oil is lost during inspection, which the reason should be analyzed. At the same time, the lubrication of each lubrication point should be strengthened. It is suggested to add grease to the lubrication point every week during the run-in period (except for special requirements).
- To keep the gear motor is clean, adjust the loose fastening parts of gear motor in time, to prevent the looseness of DC gear motor cause by the wear out of parts or causing the loss of parts.
- At the end of the run-in period, the motor should be maintained compulsive-check and adjusting, and pay attention to the replacement of lubricating oil.
In conclusion, the run-in period of DC gear motor is very important, so VEER Motor advises our customers carefully take care of your DC gear motor. Any maintaining questions of gear motor, just contact us freely.
Gear types in the internal of gear motor you should know
Gears are identified by many types and there are many specific technical words to describe their definition. The most common way to classify gears is by category type and by the orientation of axes.
Gears are classified into 3 categories: parallel axes gears, intersecting axes gears, and nonparallel and nonintersecting axes gears.
Spur gears and helical gears are parallel axes gears. Bevel gears are intersecting axes gears. Screw or crossed helical, worm gear and hypoid gears belong to the third category. Table 1.1 lists the gear types by axes orientation.
(1) Parallel Axes Gears
(1.1) Spur Gear
Spur Gear internal of Gear Motor
This is a cylindrical shaped gear, in which the teeth are parallel to the axis. It is the most commonly used gear with a wide range of applications and is the easiest to manufacture.
5 Steps easily complete the installation of geared reducer motor
Many factories are very concerned about the service life of geared reducer motor when using. In fact, the service life of gear motor is not only related to the quality of the product itself, but also related to the use method and installation method of gear motor. In order to ensure longer service life of gear motor, and then reduce the failure rate, we should according to certain procedures to installation and using. VEER Motor company get so many customers’ response for how to install gear motor after getting VEER’s gear motor, we have made some tips as below:Many factories are very concerned about the service life of geared reducer motor when using. In fact, the service life of gear motor is not only related to the quality of the product itself, but also related to the use method and installation method of gear motor. In order to ensure longer service life of gear motor, and then reduce the failure rate, we should according to certain procedures to installation and using. VEER Motor company get so many customers’ response for how to install gear motor after getting VEER’s gear motor, we have made some tips as below:
What are the installation steps of geared motor?
- Confirm whether the gear reducer motor is intact, and strictly check whether the size of geared reducer (gearbox) matches with the gear motor, which refers to sizes of bulge part, output shaft and groove, also include the tolerance of fit.
- Unscrew the screw on the dust proof hole outside of the flange, adjust the PCS system clamping ring, so that the side holes are aligned with the dust proof hole, and then insert the inner hexangular angle after tightening, remove the motor shaft key.
- Connect the motor with the reducer (gearbox) naturally, and ensure the concentricity of output shaft of the motor and the input shaft of the motor is same. And the outer flange is parallel. If the concentricity is not consistent, the motor shaft will be broken or the gear of the motor will be worn out.
- Check the veracity of the installation position of the reducer in order, and the reliability of the fasteners to ensure the all parts of gear motor rotate flexibly.
- Remove the screw plug of the air hole, replace it with an air plug, and lubricate of parts of gear motor.
5 Steps easily complete the installation of geared reducer motor
Proper installation is an important part to ensure the long service life of the gear motor. Therefore, we should install the gear motor in strict accordance with the above procedures. Of course, the regular maintenance in daily use is also important, so that to avoid damage of the gear motor during working. VEER Motor has over 10 years’ experience in gear motor production, who is a professional gear motor manufacturer. We served over 100 motor companies for OEM & ODM. And we have a professional after-sales team. If you have any question of gear motor need to resolve, just contact our technical team. Warmly welcome valuable suggestions from customers, which can make our gear motor products have more advantages in the market. Thank you!
Many applications of VEER gearmotor you need to know
The advanced degree of robots in the current fashion is breathtaking. The close coordination of various parts ensures the accuracy of repeated movements and the reliability of the completion of technological tasks. It makes people wonder how their transmission system works? If someone knows the industrial controller knowledge, their will often be found gear motor applies in many fields, such as recreation equipment, carousel in airport or express company, stereo garage, and so on. All of the above are applied to such an indispensable power transmission equipment – Gear Motor.
Many applications of VEER gearmotor you need to know
The working principle of gear reduction motors
Gear Motor is a special transmission, which transfers motor power through gear set (or worm gear) reducer, the device greatly reduces the rotate speed, thus increasing the output torque of motor, then to meet the needs of mechanical equipment.
Classification of gear reduction motors
The most commonly used types of gear motors are coaxial helical gear motor, parallel helical gear motor, bevel gear type gear motor, worm gear motor
For more knowledges or quotation you want to know, please contact VEER Motor, email: sales@veermotor.com, or visit official website: VEER Gear Motor
What is a gear motor, and how does a gear motor work?
Everyone meets gear motor at first time, who has all such a problem that is ‘What is the gear motor?‘ and ‘How gear motor works?‘. Now, let VEER Motor introduces it as below:
“Gear motor” refers to a combination of a motor plus a reduction gear train. These are often conveniently packaged together in one unit. The gear reduction (gear train) reduces the speed of the motor, with a corresponding increase in torque. Gear ratios range from just a few (e.g. 3) to huge (e.g. 500). A small ratio can be accomplished with a single gear pair, while a large ratio requires a series of gear reduction steps and thus more gears. There are a lot of different kinds of gear reduction.
Be sure to identify professional gear motor manufacturers when purchasing, the manufacturer’s price is much cheaper than the agent’s price.
In the case of a small transmission ratio N, the unit may be back drivable, meaning you can turn the output shaft, perhaps by hand, at angular velocity w and cause the motor to rotate at angular velocity Nw. A larger transmission ratio N may make the unit non-back drivable. Each has advantages for different circumstances. Back drivability depends not just on N, but on many other factors.
For large N, often the maximum output torque is limited by the strength of the final gears, rather than by N times the motor’s torque.
Veer Motor is the professional gear motor manufacturer with 13 years’ experience.
Veer Motor is the professional gear motor manufacturer with 13 years’ experience, if you want to buy gear motor with factory price, just contact us, email: sales@veermotor.com, or visit our official website: https://www.veermotor.com
How to choose the model when buying the gear motor?
Recently, Veer Motor received a lot of consulting from customer is mostly about ‘I want to buy gear Motor, but have no idea how to choosing gear motor model’, in fact, Veer Motor’s official website, there has a picture that is described in detail for how to selection of sample on each product page, customers should review them carefully. But now, Veer Motor feels the need to write an article again about how to choose the Motor model.
VEER Motor is a company specializing in the production of Small Gear Motors, Medium Geared Motors, Right Angle Gear Motors and Gear Reducers and other products manufacturers.